How to install transmission line clips code#

Install the front sections of the cooler lines to the vehicle.Дў6. Install the cooler lines to the retainer (1) located on the right side of the engine.Дў5. Install the clip (2) that holds the cooler lines together.Дў4. Install the front exhaust pipe assembly.Дў3. Install the cooling line ends (4) to the transmission.ДЎ9. A hidden yellow identification band indicates proper joint seating.ДЎ8. Ensure that the yellow identification band on the tube is hidden within the quick connect fitting.ДЎ7. Ensure that no gap is present between the cap and the fitting.ДЎ6. Ensure that the plastic cap is fully seated against the fitting.ДЎ5. Do not manually depress the retaining ring when installing the plastic cap onto the quick connect fitting.ДЎ4. Position (snap) the plastic cap onto the fitting. Pull back sharply on the cooler line in order to ensure that the cooler line is fastened into the quick connect fitting.ДЎ3. Do not use the plastic cap on the cooler line in order to install the cooler line into the fitting.ДЎ2. Insert the cooler line end into the quick connect fitting until a click is either heard or felt.ДЎ1. Install the cooler lines into the quick connect fitting.ДЎ0. Connect the rear cooler lines (2) to the front cooler lines (1).Д©. If no plastic cap exists, or the plastic cap is damaged, obtain a new plastic cap and position on to the cooler line prior to the cooler line installation.ДЁ. Notice: Ensure that the cooler line being installed has a plastic cap on each end that connects to a quick connect fitting. Install the new retaining ring (E-clip) into the remaining quick connect fittings. Ensure that the three retaining ring ears are seen from inside the fitting and that the retaining ring moves freely in the fitting slots.Д§. Do not install the new retaining ring onto the fitting by pushing the retaining ring.Д¦. Rotate the retaining ring around the fitting until the retaining ring is positioned with all three ears through the three slots on the fitting.ДҐ. Hook one of the open ends of the retaining ring in one of the slots in the quick connect fitting.Д¤. Install a new retaining ring (E-clip) into the quick connect fitting using the following procedure:ДЈ. All retaining rings being installed must be new.Д®nsure the following procedures are performed when installing the new retaining rings onto the fittings.Дў. Install the transmission oil cooler lines to the vehicle.Дo not reuse any of the existing oil lines or oil line fittings if there is excessive corrosion.Дo not reuse any of the existing retaining rings that were removed from the existing quick Connect fittings. Remove the oil cooler lines from the vehicle.ДЎ. Disconnect the rear oil cooler lines (2) from the front oil cooler lines (1).Дў1. Disconnect the oil cooler lines (4) from the transmission.Дў0. Carefully lower the transmission to gain access to the cooler line fittings.ДЎ9. Remove the front exhaust pipe assembly.ДЎ7. Support the transmission with a transmission jack.ДЎ6. Remove the clip (2) that holds the cooler lines together.ДЎ4. Remove the rear sections of the cooler lines from the retainer (1) located on the right side of the engine.ДЎ3. Remove the front sections of the cooler lines from the vehicle.ДЎ2. Remove the cooler lines from the retainer (1) located on the radiator shroud.ДЎ1. Separate the front and rear cooler lines at the quick connect fitting (2).ДЎ0. Remove the cooler lines (3, 4) from the radiator.Д©. Pull the cooler line straight out from the quick connect fitting.Д¦. Remove the retaining ring from the quick connect fitting.ДҐ. Using a bent-tip screwdriver, pull on one of the open ends of the retaining ring in order to rotate the retaining ring around the quick connect fitting until the retaining ring is out of position and can be completely removed.ДЈ. Pull the plastic cap back from the quick connect fitting and down along the cooler line about 5 cm (2 inch).Дў. Perform the following procedure when removing the cooler lines from the quick connect fittings.ДЎ. Refer to the appropriate steps when servicing individual lines. Important: The front and rear sections of the cooler lines can be serviced separately.

How to install transmission line clips code#

Transmission Fluid Cooler Hose/Pipe Replacement (Body Vin Code 3) Vehicle Transmission and Drivetrain Automatic Transmission/Transaxle Fluid Line/Hose Service and Repair Procedures If you look at pics 6 and 7, you will see the clips I'm referring to.Дў002 Chevy Truck TrailBlazer 4WD L6-4.2L VIN S They are small, hard to see, and like to fly off. Note: When you remove the retainer which holds the line on at the trans and radiator, be really careful not to lose it. The attached pics correlate with the directions. Other than that, it is going to be tight and difficult to move around under the vehicle and to guide the lines where they belong. However, I'm not sure if you have access to one.