#Ksp crossfeed enabler software#
#Ksp crossfeed enabler crack#

Charge is never lost if the engine fails on the pad.

restoreIgnitionCharge = false // if the engine has a ModuleEngineIgnitor, setting to true keeps the failure from wasting a charge.

TestFlightFailure_IgnitionFail When turning engines on, chance to turn off.

ispMultiplierJitter = 0.1 // actual reduction will be 60-80% of rated value (despite 'jitter' name, failed I_sp is constant).

ispMultiplier = 0.7 // reduce to around 70%.

TestFlightFailure_EnginePerformanceLoss For engines, reduce specific impulse until repaired.

heatMultiplier = 3 // factor by which engine heat generation is boosted.

engineID = all // the ModuleEngine(s) to fail.

TestFlightFailure_EngineCoolant For engines, increase heat generation until repaired. TestFlightFailure_DockingFeed For ModuleDockingNode, disables crossfeed until repaired. TestFlightFailure_DockingClamp For ModuleDockingNode, forces immediate undock. TestFlightFailure_SolarTracking For ModuleDeployableSolarPanel, panel cannot track Sun until repaired. TestFlightFailure_SolarMech For ModuleDeployableSolarPanel, break off panel.

TestFlightFailure_AvionicsTotal total loss of use of all 6 axis.

TestFlightFailure_AvionicsThrustJam throttle jammed at current position.

TestFlightFailure_AvionicsPartial loses a random % of sensitivity for an axis.

TestFlightFailure_AvionicsInvert inverts an axis, up means down.

maxWorkTime = 1 //max time working control can happen before toggling off.maxDeadtime = 1 //max time loss of control can happen before toggling back on.TestFlightFailure_AvionicsGlitch random on/off loss of control of an axis.

TestFlightFailure_AvionicsDeadzone a random deadzone, up to 25%, in an axis control range.

TestFlightFailure_AvionicsClamp clamps max control range of random axis.

TestFlightFailure_AvionicsAxis loses use of random axis (pitch/yaw/roll/X/Y/Z), or either all rotations or all translations.

TestFlightFailure_AvionicsXXXXX For ModuleCommand, controlling the ship from this part will cause flight problems until it's repaired:

animationName = ALL //name of animation to break.

Repair re-enables animation but does not run it.

TestFlightFailure_Animation For ModuleAnimateGeneric, will break an animation, and in many causes modules that depend on that animation to complete before performing their function. minDegradation = 5.0 //minimum percent of ablator lost shield's heat conductivity goes up proportionally.Repair stops extra heat transfer but does not replace ablator.

#Ksp crossfeed enabler crack#

TestFlightFailure_AblatorCover For ModuleAblator to crack / let heat through. TestFlightFailure_Explode Generic failure for any part, goes boom. It is normal to have multiple TestFlightFailure modules on a part, one for each failure mode, but you should never have more than one of a specific type Derived Modules TestFlightFailure is the base module for every failure in TestFlight. Not used by TestFlight, but may be used by third-party repair mods.

#Ksp crossfeed enabler software#

'software' indicates a software or electric failure that might be fixed remotely by code.

failureType // 'mechanical' indicates a physical failure that requires physical repair.

Should never be anything except: 2 = Rare, 4 = Seldom, 8 = Average, 16 = Often, 32 = Common.

weight // chances of the failure occurring relative to other failure modules on the same part.

severity // 'minor' or 'major' used to indicate the severity of the failure to the player in the MSD.

failureTitle = 'Failure' // human-friendly title to display in the MSD for the failure.

duRepair = 0 // amount of data collected when the failure is fixed.

duFail = 0 // amount of data collected when the failure occurs.

configuration // an alias for the configuration in the corresponding TestFlightCore.